Search results

  1. jerryjerry05

    91 force 70hp need help locating parts

    Most of the time, I use eBay, or boats.net .
  2. jerryjerry05

    Bad trigger? Can’t adjust timing

    New port cover gaskets, ONE TINY backfire or cough can blow these gaskets.
  3. jerryjerry05

    Coupler o-ring size?

    there's an o-ring on the outside of one of the connectors,they make 6-10 different ones, just get the assortment and try to find the one that fits?? There are 2 o-ring/seal inside the of the female connector. Google: force outboard fuel line connector and a bunch shows up. =
  4. jerryjerry05

    Bad trigger? Can’t adjust timing

    I'd bet it's sucking air someplace?? Get it running, can of starting fluid, spray the SF around the intake side of the motor, this includes under the packs and the base of thew carbs and the 4 port covers. If? this makes any difference in the way it runs?? then it's sucking air
  5. jerryjerry05

    Frank helped me out yet again

    Frank who?? Never heard of him. Yup he was one of the best !!!!!
  6. jerryjerry05

    Force 120hp won't start

    The reeds can have a small gap.
  7. jerryjerry05

    1995 force 70 hp ignition help

    Sometimes checking/testing can't find the problem. Tested a stator 3 times, tested good 3 times. Nope,it was bad.
  8. jerryjerry05

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Most times they're pressed in and don't come out easy.
  9. jerryjerry05

    1984 force 125 low compression question?

    MMO not used often in the marine industry.
  10. jerryjerry05

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    No rubber on the seats, the rubber on the needle takes the place of the seat. The pics show 3 needles. One has a groove around it. I would change that. The black tip looks like it needs replacing too? Try to replace the whole thing if you can remove them without destroying it.
  11. jerryjerry05

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    g Carb: upside down, the float should be level, hook up a hose and try to blow through the needle/seat, should be no air going through. Turn up: the drop should almost touch the post. Needle/seat: inspect the needle, rubber tip, pointy no grooves. Solid needle: look into the seat, should be a...
  12. jerryjerry05

    199 Mercury Force hard to start

    The low idle screw isn't a low idle screw. It's an air/fuel mix screw. Start at 1 1/2 turn out. Then after you figure out the running?? then adjust that screw for fine tuning. Never heard of a 199 Force 40hp. ??? If it's newer than 1994 then you might be having trouble with the primer(choke). Do...
  13. jerryjerry05

    What is this part called on Force 125

    When you replace it try to get it back to where it was before. Magic marker the threads or how ever. That way the timing job(link/sync) will be easier. Replace BOTH!!! about 35$ DON'T get used parts. They sell parts here, END-CONTROL-RH Item #: F499035 END Item #: F499036
  14. jerryjerry05

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Squeezie: it's only job is to draw fuel from the tank, you squeeze it till it gets firm, job done. Then when the motor starts it should loose the firmness. Then it just sets there. Oh yea it's supposed to stop the fuel from going back into the tank. The one way valve stops the fuel from...
  15. jerryjerry05

    1990 force 125 shift bellow leak

    Where'd you find the bellows? Old parts found on a shelf someplace might be suffering dry rot?
  16. jerryjerry05

    1984 force 125 low compression question?

    Spray WD in hole before taking comp reading?? At 30# WD ain't gonna bring the comp up enough to help anything. Like I suggested before: snake camera, someone suggested remove the head? that's the next step.
  17. jerryjerry05

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    It doesn't matter which way the vanes of the impeller set when installed. The second it is turned over to start it straightens out. The float in the carb: carb upside down: the float should be level. Carb right side up: the float drop should almost touch the tube. That's not as important than...
  18. jerryjerry05

    Which Force is most Mercury?

    The block is pretty much the only Force part. In 93+ they started changing parts to Mercury.
  19. jerryjerry05

    Force 50 priming solenoid

    You should see fuel squirt from the hose. No fuel? switch hoses around and test again.
  20. jerryjerry05

    1990 force 125 shift bellow leak

    The seal should come in it already. If not it's an easy job. Just don't dig too deep and scar the metal mating surfaces. Post a pic of the new parts. Thanks, Jerry
Top