Search results

  1. Scott06

    Registration

    Really depends on where you are. My brother went through the same registering an old Grumman 14 ft boat that belonged to my grandparents. Registration long gone etc after they passed … he went to the dmv they gave him a form , had to have a st trooper look at boat and make sure ther was no HIN...
  2. Scott06

    forward drive/bravo 4

    Anybody out there using either the Volvo Forward drive or Bravo 4 drive for recreational (aka we're not that good at it...) wake surfing behind an IO boat ? Was just curious for folks that aren't that Seriou$ about it how does it work out behind a non wakeboard boat? Even if I had the...
  3. Scott06

    Spark plug heat range

    Good deal - all typical old boat chit....
  4. Scott06

    Spark plug heat range

    That heat range mark on strap looks ok maybe a tad to hot side - wouldnt go any hotter based on what you are showing here. Actually looks really good. I cant recall where u landed for carb - did you replace it or rebuild the one you had?
  5. Scott06

    Will vehicle work?

    i think you will be fine with AWD getting up the ramp unless it is atypically steep. Ill probably get hate mail but ill share my experience with similar towing needs. ive had two highlanders that i have used for short distance towing an 06 hybrid 2 wd that had a 3500 lb tow rating. My newer...
  6. Scott06

    SEI Marine products...Anyone buy from them?? Quality??

    Some of the SEI stuff is good. A lot of guys run their drives successfully. Just heard too much BS about their impellers. After changing my original (2004) bellows last year that were still not leaking (they were stuff and rubbing on gimbal ring) I would be hard pressed to use anyone else's...
  7. Scott06

    Shift Cable Replacement

    I think you can. Also I think you also can take out the hinge pins without disconnecting the bellows from the bellhousing to get some additional room Do yourself a favor and get a factory shop manual - well worth the money for these types of repairs/questions
  8. Scott06

    SEI Marine products...Anyone buy from them?? Quality??

    I was going to make same comment - on the marine engine forum there is a excellent full time marine mechanic that stated when he installs their drives he takes the SEI water pump out and installs a OEM one. Do yourself a favor and get an OEM impeller. you're not saving that much money. On my...
  9. Scott06

    Shift Cable Replacement

    I found it helpful if you have a V engine ( inline 3.0 there is acess) after you take the inner core out, push a weed wacker wire up through the outer sleeve and tie it off on the engine , unthread and pull outer sleeve out leaving weed wacker wire in place. Put your new outer sleeve on the weed...
  10. Scott06

    Tracker Tahoe trailer tire size

    there are different load ratings for same rim size tires... also if you do go up to 15" check fender to tire interference. The trailer manufacturer should be able to tell you what size wheel and tire if the tag is missing. Also a good trailer or tire shop should be able to guide you based...
  11. Scott06

    5.7 /Chevy 350 hard starting and stalling when idle

    I would look to build your skill base on carb rebuilding & tuning vs putting money into fuel injection. I would start by measuring the strength of the spark with a inexpensive spark gap tester. If you have decent spark and any gas at all the engine will fire... Judging by the looks of it you...
  12. Scott06

    Spark plug heat range

    this is a pretty good article on reading spark plugs that discusses heat range and ground strap to look for heat range indication. http://www.wallaceracing.com/plug-reading-lm.html
  13. Scott06

    Oil Pan

    If you paint and coat the new one you wont have the issue again. Issue is the pan has a weak paint on it.
  14. Scott06

    Oil Pan

    It is a GM pan but I think the marine ones have baffling to control oil sloshing. @Scott Danforth may know the GM part number which is the best way to order it. I would get the GM part prime it really well and coat it with bed liner or rhino liner I think that is what folks do to cut down on...
  15. Scott06

    est ignition on a 1989 4.3 liter cobra.

    dont over think it, either location will work fine As long as your wires are long enough. i think MM just bolted it to the cylinder head . Volvo used the est on 4.3 s they may have a bracket that mounts the coil to back of engine or exhaust
  16. Scott06

    est ignition on a 1989 4.3 liter cobra.

    Why willit over heat on the transom? Wont be any difference in temp on transom vs mounted to engine . if you look at the pics here looks like they mount the coil to back of cylinder head https://www.michiganmotorz.com/5-7l-vortec-marine-silver-package-315-hp-1967-current-replacement
  17. Scott06

    2006 Mercruiser 4.3 no power to Fuel Pump

    Antisiphon valve is in fuel line on top of fuel tank. It takes a slight cracking pressure to open. Idea is it will prevent a leak in fuel line from siphoning the fuel tank into the bilge… problem is they can stick and not open impeding fuel flow. If the fuel pump is running but no fuel was...
  18. Scott06

    2019 Sea Doo Fish Pro Wear Ring (small marks)

    That is why it looks different vs freshwater skis
  19. Scott06

    2006 Mercruiser 4.3 no power to Fuel Pump

    Did you check your antisiphon valve ?
  20. Scott06

    Engine siezed

    Probably an uphill battle either way, but if the manifold/riser connection was bad you would see rust streaking and evidence inside the manifold and rust in exhaust ports and on exhaust valves. Would ask to see that. Leaving an engine outside under plastic wrap is a bad idea... if there is...
Top