Search results

  1. The Force power

    Force 85 hp Help Disassembling lower end.

    You are going to need one for sure! Many of us on this form made that mistake(including me) and removed that pin, mostly because it "looks like? the drain plug Maybe the were "trying to "fix" the lower-unit and did more harm than good and after realizing that.......off loaded the motor
  2. The Force power

    Force 85 hp Help Disassembling lower end.

    The Coupling (#49) will have come loose and Yoke/Shift-pin has fallen inside the LU You'll have to remove the gear assembly reverse/prop-shaft/dog-clutch but you can leave the Drive-shaft/pinion-gear and forward-gear. Tilt the Lower-unit with the opening to the sky and move it around, with aid...
  3. The Force power

    85 Force delayed stall at WOT

    Its true thou
  4. The Force power

    Force 85 hp Help Disassembling lower end.

    Don't unscrew #32
  5. The Force power

    Force 85 1987 bayliner capri

    Have your battery tested after its charged (a "full" battery 12+ volts) does not always mean its good to produce cranking-amps. a weak battery and/or Starter will not make the Flywheel spin fast enough to produce enough electricity to create spark. In addition to Jerry's advise (a tachometer is...
  6. The Force power

    Force 125 Lower Unit

    Be careful with that one, there's a good possibility the the seal around the Shift-shaft would leak See post; Force 125 1986, hole in front of lower unit weeping oil
  7. The Force power

    Remote control help

    I belief..."92 started already with a Mercury control is it not? can you send a pic.?
  8. The Force power

    1996 Force 90hp flywheel

    Than the part# and description in the ad is not correct, although it should; check the # stamped in the flywheel 261-9007-c2 is for Mariner 60 HP or others I do know the Force Flywheels! (I have & had both motors)
  9. The Force power

    1996 Force 90hp flywheel

    I don't think thats the correct one
  10. The Force power

    1996 Force 90hp flywheel

    jerryjerry05 provided you with all the info/links. Just a matter of looking it up (apparently '96/'97 have the same)
  11. The Force power

    1996 Force 90hp flywheel

    9008A36 is the # you're looking for
  12. The Force power

    1996 Force 90hp flywheel

    '96 Models are tricky as they were already Merc. ignition/flywheel and also the last time a modification was made to the ignition till it finally died in '99 Also (at least the '96) has magnet problems and flywheels got replaced often there for impossible or for $$$$ to find.
  13. The Force power

    Force 85 (1985) Doesn't like to do more than idle in water - and often dies on its own

    Here's the old post (from the late Frank) that I have printed out & live by; 1.Disconnect the ball link to the carb cam at the timing tower. Disconnecting at the cam risks bending the cam. Move the cam away from the carb roller. 2. Loosen the screw(s) on the aluminum tie bar and let all carbs...
  14. The Force power

    1989 Force 85 WOT

    Here's a old post (from the late Frank) that I have printed out & live by; 1.Disconnect the ball link to the carb cam at the timing tower. Disconnecting at the cam risks bending the cam. Move the cam away from the carb roller. 2. Loosen the screw(s) on the aluminum tie bar and let all carbs...
  15. The Force power

    125 Force Outboard won’t achieve full power

    Change the diaphragm, it will take out the guessing
  16. The Force power

    125 Force Outboard won’t achieve full power

    In theory your right (I can't explain that, maybe todays fuel and/or the low set does affect the amount of fuel at high speed) however I'm sticking with it
  17. The Force power

    125 Force Outboard won’t achieve full power

    I thought you were an advocate of running things on a richer mixture
  18. The Force power

    125 Force Outboard won’t achieve full power

    Here's a old post (from the late Frank) that I have printed out & live by; 1.Disconnect the ball link to the carb cam at the timing tower. Disconnecting at the cam risks bending the cam. Move the cam away from the carb roller. 2. Loosen the screw(s) on the aluminum tie bar and let all carbs...
  19. The Force power

    Help Pulling 1992 90hp Force out of Jetstar

    Sell it "as is" fast!! Severely underpowered / Crank is different then outboard / no Crank available
  20. The Force power

    Force 9.9HP 1991 outboard

    its mechanical, not too complicated to figure out, take your time
Top