Search results

  1. Scott06

    Will OMC Engine/Drive Match Mercruiser- Plug & Play?

    Floor is the last thing to rot from the bottom up... Ok so the boat is together they are keeping a nice motor and drive because they know the boat is roached...best to move on
  2. Scott06

    Adding 100+hp. Would you re-prop ?

    I would say yes you will likely either need to go up in pitch or down in gear ratio as you are already nipping the rev limiter... But try what you have and evaluate after install. I think the delco est which is relatively drop in does not have a rev limiter just be aware that the drive may...
  3. Scott06

    Will OMC Engine/Drive Match Mercruiser- Plug & Play?

    No offense but this sounds like a bit of turd polishing... and could be a lot of work with no result for you. As Scott outlines likely removed it and stopped doing work because transom is rotten... which can be fixed but its a lot of work. If it had a Merc alpha or bravo drive the keyhole is...
  4. Scott06

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    Not sure what A to B means here is a video showing primary and secondary ohm values
  5. Scott06

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    The one on the left is not the right power valve, there is no poppet sticking up. You need to notch a crew driver to remove the power valves with out screwing it up. There is a video at Mikes carburetor parts that shows this. Be careful if your now beat up power valve is hanging up it will...
  6. Scott06

    Push rod cover gasket replacement and distributor

    There is your oil leak.
  7. Scott06

    Oil pump

    You certainly can take the distributor out and prime it. I would just run it on the starter to get oil to the rockers and then run it before putting it in to the boat. Its pretty easy to run on the ground and check everything out before you drop it in.
  8. Scott06

    Drive lube dropping?

    After refill my alpha drive always drops level in lube bottle after first run. I top it off and then don't loose any more the rest of the season. As others have advised keep a bottle in the boat and watch the level, if it keeps dropping would take it back to person who did drive work.
  9. Scott06

    Boat won't move

    So engine would rev up freely as if in neutral or engine was under load and couldn't make the rpms happen? If revs up freely coupler, prop hub, upper gears in outdrive gone or broken vertical drive shaft. All of these except prop hub would cause an over heat as impeller in drive won't turn...
  10. Scott06

    Oil pump

    Distributor rotates clockwise when viewed from above so oil pump needs to turn same way https://www.mcmaster.com/pins/toggle-lock-clevis-pins-with-handle/ Is this a rebuild or just been sitting? another way to do this with out pulling the distributor is to pull the plugs and run it on the...
  11. Scott06

    4.3 volvo penta flywheel problems

    First thought would be a balance issue from mix and match parts as Scott outlines. Did you use the whole truck engine or pull the crank and swap that into the VP engine? Are the blocks the same casting number? The loctite will take time to fully cure especially if outside in colder weather...
  12. Scott06

    Transporting a 20' boat on a flatbed.

    Depends on what yo intend to do with the boat afterwards. If you are parting it out just winch it on . If you intend to fix it Id try to use round fence posts etc as rollers to pull it on. Another option is to jack it up, put cribbing and cross bracing such that trailer can back under it to be...
  13. Scott06

    Push rod cover gasket replacement and distributor

    This shadow area behind the balancer doesn’t get painted at the factory. Worth wire brushing and painting even if there is no rust through
  14. Scott06

    Ultra Black or RTV silicone?

    Ultra black.
  15. Scott06

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    If you forgot the float measurements yes the carb rebuild is screwed…best advice find somebody who knows carbs who can walk you thorough it
  16. Scott06

    Push rod cover gasket replacement and distributor

    Funny part is its not much work to pull an engine… ashame they wouldn’t stand behind their work .
  17. Scott06

    Push rod cover gasket replacement and distributor

    You don't have to set dwell anymore. Did you use a petronix or other conversion kit or replace the whole distributor with a delco EST? if you used a points replacement kit, timing is set the same. if you used a delco est kit you need to put it in base mode first to set timing
  18. Scott06

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    Yes but understand what all dodge was saying, unless you have an ingition system problem like weak coil bad cap and rotor or bad wires it should start with a .030 or .045” gap. Pull a plug crank and see if you have spark or as mentioned if you pour a little gas down carb or spray a touch of...
  19. Scott06

    Inboard replacing

    Whats your current ignition ? If it is a thunderbolt V it already has one.
  20. Scott06

    Inboard replacing

    Would bet if you get a 5.7 or 6.2 long block have one of the ECU programmers reprogram your ECU it would work well. All Dodge had recommended a place that does it was like $400 or maybe a tad more. Willing to bet unless you are jumping out of the water in a lighter boat like yours an alpha...
Top