Search results

  1. Scott Danforth

    Hey Newbies

    they went away in 2013. I have a few sites tagged that have bits of the manual.
  2. Scott Danforth

    I/O 18 ft. Does it sit too low in the stern?

    the motor, none the outdrive, the whole thing until you get on plane
  3. Scott Danforth

    Second Boarding Ladder . . .

    the glass at the transom to hull bottom is probably close to 3/4" yes, Cruisers are tanks
  4. Scott Danforth

    Spreading Manure, again

    aged beef?
  5. Scott Danforth

    Preparation before applying 5200

    if you need strength stronger than UV4000 you have a structural issue
  6. Scott Danforth

    Hey Newbies

    Hey @achris..... my 1988 boat with a changed motor and changed drive is having a problem....... to the newbies. your boat may or may not have the original engine. and if the engine was original to the boat, many times its a year or two older than the boat because it sat in the warehouse for a...
  7. Scott Danforth

    Cleat Mounting

    you may want to check. SeaRay burried a chunk of aluminum in the fiberglass on many boats just like other builders. for example, there is a 3/16" plate of aluminum in the gunwales on both sides of my boat for cleats and hardware.
  8. Scott Danforth

    merc sport jet 1994 vs 1995

    pull the parts diagram for both serial numbers and look. if they look different, chances are they are different.
  9. Scott Danforth

    OMC 3.8l dying at high rpm and weird cranking issue.

    pull the starter and have it tested Pull the drive and see if it turns over easier. if it does, you have a drive issue to look into check your tank vent. or the next time it dies, pull the fuel cap. if you hear hissing, your tank vent is clogged.
  10. Scott Danforth

    2003 Vp.3.0 gl water fuel separator filter questions.

    ^+1 what he said 100 hours or once a year if you have a lot of water in the tank, suggest pulling the tank sender and siphoning the water out
  11. Scott Danforth

    What Paint do I use? Repainting a plywood sail boat

    First, Welcome aboard second, top of every forum is a sticky or stickies with lots of information since you are pulling your boat every day look at link 19 in this sticky. https://forums.iboats.com/threads/how-tos-and-other-great-information.283508/
  12. Scott Danforth

    First boat buyer questions

    first boat should always be aluminum. old fiberglass boats may have structural issues.
  13. Scott Danforth

    ENGINE DIES

    welcome aboard WHY ARE YOU SHOUTING? no such thing as a mechanic in a can. not sure why you add seafoam check your fuel for water
  14. Scott Danforth

    3.0 Mercruiser Choking

    what maintenance has been done? new to you boat? first suspect is the accelerator pump
  15. Scott Danforth

    Mercury 500 thunderbolt 70s black and red won’t pee water

    make sure the key was in the impeller?
  16. Scott Danforth

    VP SX Drive | Torque Settings

    for your drain plugs/dipstick. they all get hand tightened with a screw driver. its just 3/8" threads in aluminum. in the neighborhood of 1 click on the wrist. however if you really want to pull a toque wrench, in the neighborhood of 12-13 NM if metric, 95 in-lbs
  17. Scott Danforth

    I/O 18 ft. Does it sit too low in the stern?

    weigh the boat, compare the specs. could be water logged foam, could just be the fact the boat is light, and without people, up front, that is how it normally sits due to the weight of the engine and drive.
  18. Scott Danforth

    OMC 5.0 no start

    Then pull your starter and test it
  19. Scott Danforth

    OMC Cobra 800 RETAINER PLATE issue

    WTH is a cobra 800? The stringer was a 400 or 800 There is a cobra drive or king cobra However no such thing as a Cobra 800
  20. Scott Danforth

    OMC 5.0 no start

    Battery charged? Clean battery cable connections?
Top