Search results

  1. alldodge

    Backfire through carb, thunderbolt 5

    Back firing is not from a carb issue unless it happens at high rpm. Suggest checking your timing, it should be a 8 BTDC when put in base timing. Base timing is done by connecting the Purple/White wire (no 13) to ground. Connect a jumper to the wire an adjust timing
  2. alldodge

    1993 Crownline 182 BR Electrical issues??

    Howdy Do you have a battery switch which looks something like this Need to pick up a cheap volt meter to check readings
  3. alldodge

    MPI 350 flooded??

    The best way to fix it is to disconnect the return line going back to the filter and send it back to the tank. This can be done if you have a return fitting on your tank not being used, or by connection the return line back to the gas fill hose/neck. There are some places which do this work...
  4. alldodge

    Fuel problem. Plz help!

    What is a CD filter? Also is this diesel engine or gas? Last are the picks below Yamaha filter or something else?
  5. alldodge

    Indmar 383 with SPN 66017 code

    Friends Malibu ski boat with a Indmar 383 and MEFI-5 is throwing code 66017 (Fuel Pump Relay 1 Voltage Below Normal or Shorted Low). The engine starts but will not allow it to rev more then about 1400 rpm or so. It has 3 relays, main power, Fuel pump and don't know what the third is used for...
  6. alldodge

    HELP! Oil leaking from lower unit alpha one gen one

    To small
  7. alldodge

    Need advice on transducer placement on a flat bottom skiff

    Needs to be all the way on the bottom of the hull. Appears from the holes this is where one was removed prior
  8. alldodge

    trim motor oil in mercruiser 3.0

    Dextron is used in power steering, Merc trim fluid or 10w30 or 40 in trim pump. (From Oildyne manual)
  9. alldodge

    ancient gauge. terminals aren't labeled. can someone identify them for me?

    My guess would be something like this, only issue is that pos and neg might be swapped then what is shown in this pic
  10. alldodge

    no thrust washer taper?

    Howdy Looks like you have an early style drive which probably uses props and washers in the below pic
  11. alldodge

    U Joint Bellow Question

    Here is your procedure for pins
  12. alldodge

    2005 Tahoe Q4 assistance

    No biggy Brian, we see it every now and then and most will repost to fill in the blanks for others watching. Its all one big mushy mess around here but we like it :) This might help
  13. alldodge

    3.0 liter holley carb questions

    I think your talking about the pump over ride setting as in pic below. Are you holding the throttle in the wide open position and the pump rod should be fully compressed when measuring?
  14. alldodge

    Chrylser 105 Conqurer

    Stripped everything out of it, only thing left is a bit of sanding and wire brush then start putting it back together. This is the largest piece of the two stringers, about 5 inch wide. After the stringers were removed Now the keel Boat sure wobbles a lot now. Going to have to make...
  15. alldodge

    350 mag efi, high idle 1300rpm and low top speed

    With your TBI systems and a TB-V ignition putting your engine in base timing is done a bit different. Need to connect a jumper wire to the Purple/White wire (No 13) to a good ground. While in base timing mode also adjust idle to 600 rpm, do this sitting in the water
  16. alldodge

    Carver 3607 1982

    You can use either Automatic Charge Relays (ACR) or an isolator to charge the house batteries. Stating you have three house batteries you might just want to wait until you can plug your battery charger in. The typical alternator max output is 65amps. most lead acid batteries, even deep cycle...
  17. alldodge

    2011 6.2L Mag Keep getting alarm mostly at idle

    Agree don't change your stainless pump housing, the dealer is either not to bright or just wanting to make some more money. The pressure switches seam to have a lot of trouble with them over time. There is a thread here which goes into the switch itself and discussion of bypassing, but I have...
  18. alldodge

    Need advice on transducer placement on a flat bottom skiff

    Don't install it close to your engines prop wash
  19. alldodge

    350 mag efi, high idle 1300rpm and low top speed

    Howdy The idle is controlled by the ECM and is not adjustable, but 1300 is way to high. I wonder if someone left the engine in base timing mode. Look for the DLC connector and see if it has a jumper wire on it or another connector on it. If there is no connector or jumper, disconnect the...
  20. alldodge

    What happened to the beeper

    Thanks, I have manual 23 and have been looking at it. I have had both harness replaced, engine and Fuel injection with MEFI-3. The difference I have yet to be able to determine is the engine to MPI connector. Manual 23 shows one connector and there is a different number of wires being shown...
Top