Search results

  1. demarko210

    03 150 Saltwater EFI thermostat housing

    So i found the issue. See the image attached. It seems as if the housing is taller on the portside. Can you see the difference? Now i dont know if i should buy a housing and see if they are the same or try to find a bolt.
  2. demarko210

    03 150 Saltwater EFI thermostat housing

    I am going back over to the boat and clean the housing and surface area and see if i can get better results. I will update in a few hours. Thanks i will look at the heli-coil kits and see if its something i can do.
  3. demarko210

    03 150 Saltwater EFI thermostat housing

    correct. I just cleaned the bolts with degreaser and wire brush. One bolt had metal thread halfway around the one thread about 1/3 the way up. I did not try with out the rubber.
  4. demarko210

    03 150 Saltwater EFI thermostat housing

    I will investigate that. The image is before i removed the thermostat. Looks good but now it does not close the same.
  5. demarko210

    03 150 Saltwater EFI thermostat housing

    Yes i tried the other 3 bolts to try and fit into that location. Same thing they did not catch the thread. It catches when i just thread the bolt though. I didnt mean i will grind but just clean up the surface area and see if it helps. Also I will clean the threads on the bolts with wire brush.
  6. demarko210

    03 150 Saltwater EFI thermostat housing

    Captains, Ok while changing out the port side thermostats i was trying to get my cover back on. What is happening is when i place the cover over the thermostat on the port side the left side screw seems to not want to thread into the hole. When i remove the cover and thread the bolt into the...
  7. demarko210

    2003 150 saltwalter water pump tube

    Thank you, I have a Selco manual. Number 42 in your diagram came with the new pump but it was already inside the housing. My image, i believe the old one from the old housing (42 & 50) is what is stuck on the water tube. I wanted to be sure because when i pulled on it the other day it was hard...
  8. demarko210

    2003 150 saltwalter water pump tube

    When i pull the lower unit in the fall I replace the water pump as it broke up while running in on muffs. I have since replaced thermos, water pump, seals in the lower and vacuum and pressure tested it. Now I want to reinstall it. I have attached a image of the water tube inside the mid section...
  9. demarko210

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    Why is it that walk around boats with the same hull as center consoles max horse power rating seems to be lower? What is you max rated?
  10. demarko210

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    Did you have the chance to run the engine on that boat before the hull repair?
  11. demarko210

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    What engine are/will be running?
  12. demarko210

    Reseal cabin door frame

    I like those lights. I was amazed when I turned them on how much I could see. I was using one of those lights that take a battery and you press to turn on/off. I could not get that thing in the right place to see to save my life. It would find it way directly into my eyes though. This works...
  13. demarko210

    Reseal cabin door frame

    So it was not a straight forward remove and install. At the top had about a half inch gap on each corner which made a half inch gap at the top of the ceiling where the frame meets the dash. Exactly where rain water was getting in and running down the ceiling. I had to sand down about a half inch...
  14. demarko210

    Reseal cabin door frame

    @kcassells thanks man these string LED s are great.
  15. demarko210

    Lower unit 03 150 saltwater lower unit

    Thank you. The one behind it was facing the same way and missing the rubber seal that sets around the prop shaft. I have replaced both seals. I have vacuum and pressure check and she holds.
  16. demarko210

    Reseal cabin door frame

    I thought butyl was also used for windows or just a sealant. Here is the version that I purchased. Mines wont be in direct sunlight if that makes a difference hehe
  17. demarko210

    Reseal cabin door frame

    Thanks KC never thought of that Christmas lights lol. Yet I am here rigging a 12v light up. It will be here tomorrow.
  18. demarko210

    Lower unit 03 150 saltwater lower unit

    It seems my prop shaft seals are leaking. I did a pressure test and bubbled up right away. I pulled the seals the hack way and saw that the seals were in wrong. The metal seal was in first and the rubber seal was in second and they were lined up front to back. The metal seal that was in first...
  19. demarko210

    Reseal cabin door frame

    Got it home clean and scraped it with degreaser. Waiting on my adhesive tape and 4200 to be delivered today. In the mean time I will see if I can figure out how I need to install some lighting under the boat cover so i can clean and prepare the door way for install. I will add the tape in a L...
  20. demarko210

    Reseal cabin door frame

    Still working on it KC. I been having issues seeing while underneath the boat cover and trying to hold the flashlight. Then the flashlight is so bright under the cover that is blinds be at certain angles. I will get one of those headband flashlights. I think i will put it off until late March or...
Top