Search results

  1. C

    1979 55HP Johnson

    couple things...oily soot is just carbon deposit washout and should eventually stop in nothing abnormal top side. fuel leak..excessfuel leak with engine tilted up can happen with full carbs but a carb should normally stop the inflow of fuel if the inlet needle closes properly... if...
  2. C

    Evinrude 9.9 HP Model # 10924B

    assuming you have done a good carb cleaning and ignition is ok check (open) venting on the tank and small fuel pump screen and try hand pumping the fuel to the fuel pump if it clears the problem ( it stays running) the fuel pump may need a new diaphragm or replacement altogether...
  3. C

    Hard start but runs great once started

    try hand pumping up some fuel in the carb ... before starting it. using choke ?
  4. C

    '86 Evinrude 60 VRO E60TLCD with water in #3

    delete
  5. C

    Battery Cables

    you can buy OEM stuff but good booster cables say 6 ga should work and cheaper. Use 4 ga if the cable run is " long" . You could slide a sheet or two of shrink tubing ( about 1 inch size) sold by the foot and shrink it over the booster cable for added protection. Ends will need...
  6. C

    Is this oil okay for my 1960 Johnson Sea-Horse JW-16, 3 HP, 2-cylinder? And is 16:1 the right fuel mix?

    thanks for clarifying.
  7. C

    Is this oil okay for my 1960 Johnson Sea-Horse JW-16, 3 HP, 2-cylinder? And is 16:1 the right fuel mix?

    https://www.youtube.com/playlist?list=PLbqaYPHqDnWtc6-fa5pCrVr5_g5lF5Xgs
  8. C

    Is this oil okay for my 1960 Johnson Sea-Horse JW-16, 3 HP, 2-cylinder? And is 16:1 the right fuel mix?

    1960s use 50/1 oil won't hurt it and go 25/1 but spark plugs may get plugged up with carbon after a while. if it is grandpa's motor may as well pull the FW and check coils for cracks , change condensers and clean-up the points change impeller and GC oil set points at the high...
  9. C

    1965 Evinrude 9.5 Throttle Issue

    fyi ... https://www.aomci.org/wp-content/uploads/attachments/1972%20Evinrude%209.5HP%20Service%20Manual.pdf
  10. C

    1999 Johnson 200hp, Ocean Runner Lower Unit Hub

    what is the engine mdl # because lots of 1999 200hp shows 435022 s the correct part
  11. C

    Roll pin

    the procedure to drop the GC on older CD will show you the area of concern. not a big deal to lift the PH but if you damage the base gasket a new one ...and the correct one will be needed ( patterns differ!!)
  12. C

    Roll pin

    roll pin holds the brass cup in place which retains the spring which retains the carbon seal etc.....
  13. C

    1970 6hp Evinrude 6003B Shear pin.

    hubbed prop I guess i'll have to check my prop more closely but personally I prefer brass should I ever hit something .
  14. C

    1970 6hp Evinrude 6003B Shear pin.

    I just cut myself a few a few weeks ago 3/16 brass rod 1.380 inch long for a refurbed 6Rxx so if your spare Fabril 2-16-17 are that size they will fit.
  15. C

    Manifold leak

    they need to be torques to specs...and do not strip the threads on the block!! !!
  16. C

    1957 Johnson 35hp short to long shaft

    unless something bad happened storage for 4 years should not have locked it up. did you try removing the starter recoil group on top.... it may be why it does not turn
  17. C

    1957 Johnson 35hp short to long shaft

    at a bare minimum pull the cyl head for a peek on that stuck engine. . I have unstucked a 9.5 with simple & firm hammer wacks and wood peg with patience and wd 40 . Took 4-5 days for wd 40 to soak in and free it up but has run great ever since. motor was $50 CDN drop the GC cases...
  18. C

    87 Evinrude Ignition Switch Problem

    the switch just transfers incoming B+ to accessories (A) and choke (C) and start function (S) ( also kills the engine when OFF) if nothing happens check that you did not blow a fuse (if any) or at least the key is getting B+ on the B post ... if not trace back and find out why! use a...
  19. C

    Johnson 6hp 1969 model 6r 69m - 1 carb works, another doesn't

    make certain the side vertical channel feeding fuel to the upper idle screw and chamber below the welch plug is clean 100% ! and idle screw packing & nut is tight
  20. C

    1965 Evinrude 9.5 Throttle Issue

    patience brings joy ... glad you got it !
Top