Search results

  1. jerryjerry05

    89 125 won't go into forward gear

    From the pics: both dog and gear are ok. Nordin mention the shift rod, not sure of the turns needed in or out for the right setting. Under the bottom carb is the top of the upper shift shaft, you might have to adjust it there?? Once in a while I've ran across the shaft needed adjusting. Just in...
  2. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Thought I mentioned bad connections on the trigger leads??? 1988/85hp: started off with an intermittent miss, once the motor got hot the miss went away. Then the miss became more pronounced and would miss every now and again under power. Then it became a constant miss. One lead from the...
  3. jerryjerry05

    85hp force will not start. Fuel not getting to cylinders.

    You didn't mention the choke or primer? What system do you have? The primer can leak and cause a no start situation?? Not using the choke you won't get the enriched air/fuel needed to start.
  4. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    This problem and similar problems, when it happens is the hardest thing to troubleshoot.
  5. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Loosing spark after a moment= regulator, short in the wiring harness, stator, trigger, blown fuse(some Bayliners, not many, had a fuse under the dash). outboardignition.com has test procedures for your motor. Some, when they rigged the boat for tops and windows they would drill into the wiring...
  6. jerryjerry05

    ‘83 Chrysler 7.5 replacement follower for carb throttle linkage

    3D printer?? My brother-in-law has a 3d printer and from what I've seen that should be no problem to fabricate. Machine shop? Fabricate from aluminum.
  7. jerryjerry05

    Major two stroke screw up Force 120

    As long as there's oil you should be ok. The TCW3 was designed to burn "clean" and regular oil and the older TCW2 and the oil originally used when burned it would leave a residue and eventually carbon would seize the rings and POW there goes another outboard. :( Bought a new 88 with twin 85hp...
  8. jerryjerry05

    Force 70hp trim motor!

    Most time the housing/reservoir comes with the motor. PT497NK or PT495NK-2 Google
  9. jerryjerry05

    105 water pump

    The housing's fine. They work with a lot more pitting than that little bit you got. But like Nordin suggested you can fill the holes with something like Marine Tex and sand it down. Way too much work for the results. The part# for the impeller is F438065 this changes to F 438165-1 the 6 blade...
  10. jerryjerry05

    2.3 cobra shift problem now...?

    The shift problem could be the bellcrank is bent??? The pic above shows the bellcrank. Take it apart and see if the part that is inserted in the housing is at 90d??? Is the interrupter switch killing the motor when you shift? Sometimes the tiny button slips off center and the switch won't stall...
  11. jerryjerry05

    1994 Corsair. Can't find intake

    Maybe post a pic of the manifold. Maybe a bit more info on HP motor anything?? I found a Sunbird Corsair with a 4.3L Chevy(this you??)
  12. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    How are you testing for spark?? A spark tester? or holding the plug on the block? The trigger leads are very thin and under the shrink wrap on the connector the thin wire breaks and you can have intermittent spark. Thought you fixed the faulty wire connections? I replace ALL of the connectors...
  13. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    IF?? your running it in the driveway , just bend over and look above the prop. The snout should be hanging there? You ask for help but don't seem to really want to do anything but the far fetched things. ?????
  14. jerryjerry05

    Chrysler 65hp clutch dog problem

    From the looks of the dog and gear, they both don't look bad????
  15. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Hotter plugs like higher octane really won't help. Last time I ask, you check for a snout?
  16. jerryjerry05

    Chrysler 65hp clutch dog problem

    That old it's might be hard to find the dog. Try Franz Marine?? They seem to be able to find something that old??? That said, Dremmel and cut down the edges or a machine shop. In some cases the dog can be flipped around and used if not in too bad of shape???
  17. jerryjerry05

    Bad mixture? Help

    Sucking air someplace?
  18. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Here at the home they sometimes let us stay up late, once until 8:15 :) How about checking for the snout?
Top