Search results

  1. 04fxdwgi25

    Is this oil pressure normal?

    All I am saying is if that dip stick went into oil, it would be covered, not just on just one edge. Did you wipe it off prior to taking photo is all I was asking. If you did, that explains the clean side w/ the marks and level is high. If you did not wipe it off, you are low on oil
  2. 04fxdwgi25

    Is this oil pressure normal?

    I see where the marks are and there is no oil on the dipstick up at those marks. Or did you wipe the oil off the top part of the dipstick where the marks are and leave it on the bottom edge only?
  3. 04fxdwgi25

    White Ground wire

    To each his own. Can you cite the MTBF study(s) you refer too? Solder and sealing shrink work wonders.
  4. 04fxdwgi25

    Is this oil pressure normal?

    Looking at that dipstick, I read it as you are way low on oil. Dipstick should be covered, not just that bottom edge, which may just be residue in the dipstick tube and not actual level.
  5. 04fxdwgi25

    Mystery trim/tilt motor

    Believe that is an old Prestolite trim pump. Were very common. Can easily swap to a more modern one with the poly tank. It does have the Merc 3 pin connector on it. What power package is in the boat?
  6. 04fxdwgi25

    Steering issues on a SeaStar steering

    Doubt it's the steering system. Maybe a bent skeg on the lower end of the motor? Something dragging in the water, like a transducer or a trim tab? Is the outboard mounted square on the transom?
  7. 04fxdwgi25

    White Ground wire

    Don't know many pro guys that use the boat trailer chassis as a common ground point. Too many corrosion / connection related problems. On a camping trailer, ok, but not a boat trailer. They do bond the ground to the trailer frame, but for the most reliable system, all the lights (and electric...
  8. 04fxdwgi25

    Random Hole in the block 1998 4.3 Vortec

    that's for the oil dip stick
  9. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    The zerk fitting next to the sender is for the bushing. Pump in some marine grease and move drive up and down. Repeat till some grease squirts out around the bushing. Best fix would be to pull out the pins, one at a time, clean them up, grease the heck out of them and install per manual. Repeat...
  10. 04fxdwgi25

    Another electric fuel pump issue

    Try running it with the fuel fill cap off and see if it helps. Sometimes the fuel tank vent gets clogged, causing the tank to pull a vacuum when running.
  11. 04fxdwgi25

    How much power steering fluid does the system take (dual 5.7 Alpha 1 Gen 1)

    If there is no indication of PS fluid in the bilge, a pressure test on the PS cooler may be warranted. Could be losing PS fluid to the cooling water if the cooler has a leak in one of the tubes, but I would think there would be indication of water in the fluid, too. Maybe not.
  12. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    The manuals you downloaded have troubleshooting steps in them for the pump. There are quite a few things that can cause that, up to and including the wiring that runs to the switch in throttle / shift handle.
  13. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    Glad you got a handle on it. I would get a new set of bushings. Not too expensive. Those ones have material deposited in them. You can try putting some waterproof grease on them, but they are crusty old things.
  14. 04fxdwgi25

    Chris craft scorpion wiring diagram

    Nice easy to follow drawing there. would cover 95% of the carbed MC rigs.
  15. 04fxdwgi25

    Chris craft scorpion wiring diagram

    90% of the engine / helm gauges and such are available in the Mercruiser manuals. Chris Craft specific wiring would be the unicorn info, but normally done to AYC stds for color codes, breaker sizes and wire sizes.
  16. 04fxdwgi25

    Orange and pink wire

    Wire certainly has 2 ends to it. Look under the dash to see if same colored wire is connected to a switch / piece of equipment or breaker. Then read what the breaker/switch is for. Problem solved.
  17. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    Sent you a PM you may be interested in.
  18. 04fxdwgi25

    Popped through the intake.

    Have seen coils get a "carbon track" on them blow the spark right out from under the boot.
  19. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    Suggest getting the service manual for the drive that shows everything and explains how to service. Looks to be an Alpha gen2 out drive. I have the manual if you need it.
  20. 04fxdwgi25

    Is this a trim ram issue? Popping and grinding noises from stern drive. pics and video attached!

    That cap thingie is the trim gauge sender. The hinge pin is under it, screwed into the bell housing (the part that is lifted)
Top