Search results

  1. alldodge

    Bravo Three Drive (SN:0W958159) Shaft Bearing Assembly

    Looked up your serial number (I should have done that first) and you/we need manual 39. In manual on page 3B-14 it does show a shim (item 42) which would be used for pinion depth http://162.144.28.33/lib/mercruiser/manuals/mercruiser39.html#/204 Preload with new bearings is 6-10 in-lb, old...
  2. alldodge

    No power at fuel pump

    It appears from the look of the back of the plastic has gotten hot, probably from the relay. If you can jump between the two points without the relay installed, and the fuel pump fuse installed, and it does not blow the fuse then the relay is the problem
  3. alldodge

    Stringer replacement

    Haven't had much luck with an idea book myself. I select the paper clip in the upper right hand corner. This then opens to buttons in the bottom of the reply screen for uploading attachments (pics). The other method is select the pic icon and then past the location. Maybe copy the pic in the...
  4. alldodge

    Stringer replacement

    Is "this boat" a row boat, 60 trawler, maybe something longer/shorter? Kind of need to see what your looking at
  5. alldodge

    5.7 - Sea water pump replacement - Rookie mistake :(

    BT has you covered, but can also look on the back of the housing, Most all motors are now Left Hand Rotation and only if you have a very old boat will you run into a RH motor.
  6. alldodge

    tilt/trim problem

    This tells me the trim limit is not adjusted correctly or not working. The Blue/White wire connects to the Red/White wire for UP. For it not working, I would say you may need another trim switch, or the connections to the switch are not making connection
  7. alldodge

    3" thru hull exhaust too loud, want to tone it down

    The block off plate is on the engine side The exhaust tube or bellows connects the inside Y pipe to the outdrive
  8. alldodge

    transom leak

    Use a wire to fish it thru
  9. alldodge

    Mercruiser 3.0 TKS Studder coming off plane

    There is a procedure to adjust idle but it is done in gear and adjusted to 650-700 rpm. The 900 does seam a bit high in neutral so may need adjusting, or timing needs to be checked. Would guess timing should be set 2 ATDC being a 2009, but would need your serial number to verify (0L43100 and...
  10. alldodge

    No power at fuel pump

    Need a voltmeter to see were power is and what level. When you lump the fuel pump are you going straight to the battery power? If so check the fuse Here is a C-D model (V8 but V6 would be same) but unsure which is a 2000
  11. alldodge

    Mercruiser alpha one knocking noise

    Wish you would have lead off with this, but your tool is dead on for the first two steps, the gimbal is the third step
  12. alldodge

    VelvetDrive Transmission leaking fluid from dipstick

    Don't know a ready available manual which can be downloaded. Merc oil is 25W40 but many use others from 15W40 diesel oil to 20W50 racing oil. This is what Merc recommends. I use straight 40W in my Rinker because if I need a sweater I'm not going boating
  13. alldodge

    Is this suppose to do this??? need help

    Agree, and will add, adjust the flats on the on the right side where they are straight up and down. The cylinder should not be able to rotate once adjusted. Should have to loosen the cable jacket nut to rotate
  14. alldodge

    Tach code for TAMD73P

    As with all diesels the tach works off a Tach generator, the Alternator W terminal or inductive pick up. I'm sure you have seen the chart attached and it does not list your specific motor. So you need to first find out what is supplying the tach signal or the 3 listed. If it is the alternator...
  15. alldodge

    Hydraulic Manifold and Anode Installation

    You don't need the anode if your not installing a Mercathode. There is no drilling involved in any part or the install. The seal p/n 12077 goes in from the bottom
  16. alldodge

    Tilt Trim Circuit Breaker?

    Here is a diagram I have for OMC
  17. alldodge

    Windlass question about double decks??

    Never heard of someone doing it this way, but I would think the lower hole needs to be sized based on how much fall the rope has at its shortest. Meaning, after almost all anchor line is in the locker (piled up) how much distance is between the pile and the top hole. Then take the rope (rode)...
  18. alldodge

    350 mag mpi surging under load

    Back Howdy No, while the cap outer appearance is not round, the rotor does turn in a circular fashion and the shaft of the dizzy can go it from 0 to 360 So long as it rotates , the base can be rotated
  19. alldodge

    4.3 mercrusier crank no start

    It's hardly never the coil 10.56V is pretty much a dead battery, your should have at least 12.5V after charging It cranks over but how fast, is it kind of slow? Should have a TB-IV ignition but I would work on the bat first Now if you meant 12.56V then run thru this troubleshooting guide...
  20. alldodge

    transom leak

    OK, couldn't quite figure what you were asking either. Those are cable adapters, they change the bayonet to ring type terminals. The older sender wires use to be attached by terminal boards or screws and nuts.
Top